WHAT IT TAKES
TIME: 1/2 day
SKILL LEVEL: Beginner
Lots of kitchens have a little wall space that would be perfect for a storage or display shelf. Plenty of bathrooms do too. This shelf is a great project for a beginning woodworker, and since it’s so easy to adapt to different uses, a more advanced DIYer can have a lot of fun customizing it.
You’ll need a jigsaw, a drill and two accessories for the drill. The first is a No. 8 combination drill bit and countersink (shown here), which you can find anywhere drill bits are sold. The second accessory is a small sanding drum (shown on here and in Photo 3), which you can find at home centers or online. The only other tool you might need is a nail set, for setting the heads of finish nails below the surface. Obviously, if you have a band saw and a miter saw, they will make this project a piece of cake.
You can build this shelf from just about any type of wood. Resist the urge to use the least expensive knotty pine, unless that’s the look you’re after. Knotty pine will be harder to work with and to paint well. Instead, get clear pine, poplar or any other knot-free board. If you’re planning to paint the shelf, avoid oak. We used clear alder.
Begin by cutting the shelf to length with a jigsaw (Photo 1). Then cut a piece 6 in. long from which you can cut the two brackets (Photo 2). Jigsaws often make a rougher cut on the top surface, so label that “top.” The roughness will be hidden by the edging, even if the top of the shelf is visible after hanging it. But use a fine-tooth blade and set your oscillating feature (if your saw has it) to zero.
You can trace the curve for the brackets from the full-size pattern here, or even easier, use the bottom of a coffee can or a small plate. The exact curve isn’t important. After the brackets are cut, smooth the sawn edges with a file, sanding block and the sanding drum in your drill (Photo 3) until the wood is smooth. You can stop sanding at about 150 or 180 grit.
Start edging the shelf by cutting the end strips to length. Instead of measuring, just hold the molding to the end of the shelf and mark it for cutting. It won’t hurt if it’s a hair too long. Mark one edge of the shelf as the front edge, then nail on the side strips (Photo 4), keeping the front edge flush. Make sure the rounded edge faces out. Put a thin bead of glue on the shelf edge before nailing, and keep the bottom edge as flush as you can. If the strips are a little long in back, you can easily sand or file off the excess, and if they stick out a little on the bottom edge, that can be sanded off too. Finally, nail on the edging strip in front.
Now set the nails and put a little painter’s putty on them. When the putty is dry, sand the edging so the corners are smooth and the bottom edge is flush with the shelf. The bottom of the shelf will have a seam between the shelf and the edging. It’s pretty much impossible to eliminate that seam permanently. Expansion and contraction of the wood will open it up even if you caulk or putty it, so don’t be too much of a perfectionist. However, if your cut on the 1x6 is particularly rough, some putty there will help clean things up.
The next step is to drill some screw holes in the shelf for attaching the brackets. The idea is simple: two screw holes on each side of the shelf so you can screw down into the brackets. Here’s what to do. First, hold a bracket where you want it to be, but on the top of the shelf. Trace around the bracket, then do the same thing for the other bracket. Mark the screw locations and drill screw holes in the shelf from the top, using your combination drill/countersink bit.
Now hold a bracket in position on the bottom of the shelf, make sure the back edge is flush with the back edge of the shelf and that the screw holes are centered on the bracket. You can do it by eye, but if that’s hard, put the two screws in their holes and use the points of the screws to guide you. Drive the screws by hand into the bracket (Photo 5), then repeat with the other bracket. Now is a good time to step back and admire your work, because you’re almost done. But if for some reason you messed this part up, just drill new holes and fill the old ones with putty. You can shift the position of the brackets if you want.
Begin this part of the project by unscrewing the brackets. It’s always easier to paint a project well if you can do the parts separately. Sand the pieces thoroughly to about 150 to 180 grit, removing sharp edges and corners, but not rounding them over too much. Wipe the sanding dust off with a rag and vacuum the parts thoroughly. Now set up your painting area. We highly recommend using spray paint for this project because it’ll get you the smoothest finish.
Cover your work surface with paper or plastic, and set your shelf on strips or blocks to get it up off the surface. The shelf is pretty easy to paint, but go light on the edges to avoid drips. After the first coat of paint is thoroughly dry, sand it lightly with fine sandpaper, just enough to take off any roughness. Wipe and vacuum, then apply two final coats.
There’s a trick to painting the brackets: Drive a long screw in one of the holes and use it as a little handle. That way you can spray the whole piece evenly in one shot (Photo 6). Then carefully set it down on a couple strips of wood to dry. When the paint is dry on all the parts, reassemble your shelf.
We recommend using small angle brackets to hang your shelf (Photo 7). Normally the top of a shelf is above eye level and the brackets are hidden, especially with items on the shelf. If your brackets are more exposed, give them a little spray paint to match the shelf, and paint the part that goes on your wall to match your wall. They’ll be barely noticeable. Generally, though, this step isn’t necessary.
To hang the shelf, use drywall anchors. Don’t worry about hitting studs; there shouldn’t be enough weight on this shelf to require it. Just put the shelf where you want it to go, make sure it’s level, mark through the brackets where the anchors will go, and install the anchors. If it seems like you need a third hand to manage everything, you could draw a level line on the wall where the shelf will go. With the anchors in place, use the screws that came with the anchors to attach the shelf. Your shelf is complete! When you’re ready to build more, check out the variations starting here.
Go ahead—play with this project! It’s easy to make your shelf as long as you want it to be. Just put more brackets underneath it, maybe one every 2 ft. or so. You could also scale it up by using 1x8 lumber, or even wider stock, as long as you also scale up the brackets. Some other variations are shown below. However, we have one strong recommendation: If you’re doing anything more than changing the size or color, first make a prototype out of inexpensive pine. Your plates, pot lids, cooking tools or whatever will be different from ours, so make sure they fit.