Bibliography

  1. [ABD 15] ABDULHAMID H., Etude de la tolérance aux dommages d’impact sur structure composite en zone de reprise de plis, Thesis, University of Toulouse / ISAE, 2015.
  2. [ABI 08] ABI ABDALLAH E., Optimisation de tubes composites en compression à la tolérance aux dommages, Thesis, University of Toulouse / ISAE, 2008.
  3. [ABR 98] ABRATE S., Impact on Composites Structures, Cambridge University Press, 1998.
  4. [AGA 08] AGATI P., LEROUGE F., ROSSETTO M., Résistance des matériaux: Cours, exercices et applications industrielles, Dunod, 2008.
  5. [ALI 97] ALIF N., CARLSSON L.A., “Failure mechanisms of woven carbon and glass composites”, Composite materials, Fatigue and Fracture, vol. 6, ASTM STP 1285, pp. 471–493, 1997.
  6. [ASH 00a] ASHBY M.F., JONES D.R.H., Matériaux, tome 1 : propriétés, applications et conception, Dunod, 2000.
  7. [ASH 00b] ASHBY M.F., JONES D.R.H., Matériaux, tome 2 : microstructure et mise en œuvre, Dunod, 2000.
  8. [AST 05] ASTM D7137/D7137M, Standard Test Method for Compressive Residual Strength Properties of Damaged Polymer Matrix Composite Plates, ASTM, 2005.
  9. [BAM 08] BAMBEGER Y., VOLDOIRE F., Mécanique des structures: Initiations, approfondissements, applications, Presses des Ponts et Chaussées, 2008.
  10. [BAT 13] BATHIAS C., Matériaux composites, Dunod, 2013.
  11. [BER 99] BERTHELOT J.M., Matériaux composites, Tec & Doc, 1999.
  12. [BIZ 09] BIZEUL M., Contribution à l’étude de la propagation de coupures en fatigue dans les revêtements composites tissés minces, Thesis, University of Toulouse / ISAE, 2009.
  13. [BOU 09] BOUVET C., CASTANIE B., BIZEUL M. et al., “Low velocity impact modeling in laminate composite panels with discrete interface elements”, International Journal of Solids and Structures, vol. 46, pp. 2809–2821, 2009.
  14. [BOU 16] BOUVET C., “Tolérance aux dommages d’impact des structures composites aéronautiques”, Techniques de l’ingénieur, 2016.
  15. [CAS 13] CASTANIE B., BOUVET C., GUEDRA-DEGEORGES D., “Structures en matériaux composites stratifiés”, Techniques de l’ingénieur, 2013.
  16. [CHA 87] CHANG F.K., CHANG K.Y., “A progressive damage model for laminated composites containing stress concentrations”, Journal of Composite Materials, vol. 21, no. 9, pp. 834–855, 1987.
  17. [CHE 08] CHEVALIER L., Mécanique des systèmes et des milieux déformables: Cours, exercices et problèmes corrigés, Ellipses, 2008.
  18. [CHO 92] CHOI H.Y., CHANG F.K., “A model for predicting damage in graphite / expoxy laminated composites resulting from low-velocity point impact”, Journal of Composite Materials, vol. 26, no. 14, pp. 2134–2169, 1992.
  19. [DAN 94] DANIEL I.M., ISHAI O., Engineering Mechanics of Composite Materials, Oxford University Press, 1994.
  20. [DEC 00] DECOLON C., Structures Composites, Hermès, 2000.
  21. [DEQ 12] DEQUATREMARE M., DEVERS T., Précis des matériaux, Dunod, 2012.
  22. [DOR 86] DORLOT J.M., BAÏLON J.P., MASOUNAVE J., Des matériaux, École Polytechnique de Montréal, 1986.
  23. [ESD 95] ESDU, “Buckling of rectangular specially orthotropic plates”, available at: www.esdu.com, 1995.
  24. [EVE 99] EVE O., Etude du comportement des structures composites endommagées par un impact basse vitesse-applications aux structures aéronautiques, PhD Thesis, University of Metz, 1999.
  25. [FED 78] FEDERAL AVIATION ADMINISTRATION 25 (FAR25), Damage tolerance and fatigue evaluation of structure, Advisory Circular 25.571, 1978.
  26. [FED 88] FEDERAL AVIATION REQUIREMENT, “Equipment, systems and installations”, Advisory Circular (AC) 25.1309, available at: www.faa.gov/, 1988.
  27. [GAY 97] GAY D., Matériaux composites, Hermès, 1997.
  28. [GER 57] GERARD G., BECKER H., Handbook of Structural Stability, National Advisory Committee for Aeronautics (NACA), Washington, DC, 1957.
  29. [GON 12] GONZÁLEZ E.V., MAIMÍ P., CAMANHO P.P. et al., “Simulation of dropweight impact and compression after impact tests on composite laminates”, Composite Structures, vol. 94, pp. 3364–3378, 2012.
  30. [HEX 16] HEXCEL COMPANY, “Hexcel product data of the M21 epoxy resin”, available at: www.hexcel.com/Resources/DataSheets /Prepreg-Data-Sheets/914_eu.pdf, 2016.
  31. [JOI 78] JOINT AIRWORTHINESS REQUIREMENTS 25 (JAR25), Part 1: requirements, Part 2: acceptable means of compliance and interpretations (for composite structures: JAR25 § 25.603 and ACJ 25.603), 1978.
  32. [PET 05] PETIT S., Contribution à l’étude de l’influence d’une protection thermique sur la tolérance aux dommages des structures composites de lanceurs, Thesis, University of Toulouse / ISAE, 2005.
  33. [PIN 06] PINHO S.T., ROBINSON P., IANNUCCI L., “Fracture toughness of the tensile and compressive fibre failure modes in laminates composites”, Composites Science and Technology, vol. 66, pp. 2069–2079, 2006.
  34. [ROG 08] ROGERS C.E., GREENHALGH E.S., ROBINSON P., “Developing a mode II fracture model for composite laminates”, ECCM13, Stockholm, Sweden, 2–5 June 2008.
  35. [ROU 95] ROUCHON J., Fatigue and Damage Tolerance Aspects for Composite Aircraft Structures, Proceedings of the ICAF Symposium, ICAF-DOC-2051, Delft, The Netherlands, 1995.
  36. [SES 04] SESANIO J., Matériaux composites à matrice organique, Presses Polytechniques et Universités Romandes, 2004.
  37. [SOD 04] SODEN P.D., KADDOUR A.S., HINTON M.J., “Recommendations for designers and researchers resulting from the world-wide failure exercise”, Composites Science and Technology, vol. 64, pp. 589–604, 2004.
  38. [TAN 15] TAN W., FALZON B.G., CHIU L.N.S. et al., “Predicting low velocity impact damage and Compression-After-Impact behaviour of composite laminates”, Composites Part A: Applied Science and Manufacturing, vol. 71, pp. 212–226, 2015.
  39. [TOR 16] TORAY CARBON FIBERS AMERICA COMPANY, “TORAYCA datasheet of the T300 carbon fiber”, available at: www.toraycfa.com/pdfs/T300DataSheet.pdf, 2016.
  40. [TRO 94] TROPIS A., THOMAS M., BOUNIE J.L. et al., “Certification of the composite outer wing of the ATR72”, Journal of Aerospace Engineering, Proceedings of the Institution of Mechanical Engineers Part G, vol. 209, pp. 327–339, 1994.
  41. [US 97] US MILITARY HANDBOOK MIL-HDBK-17, Composite Material Handbooks, Department of Defense of USA, 1997.
  42. [WIS 12] WISNOM M.R., “The role of delamination in failure of fibre-reinforced composites”, Philosophical Transaction of the Royal Society, vol. 370, pp. 1850–1870, 2012.
  43. [XU 14] XU X., WISNOM M.R., MAHADIK Y. et al., “An experimental investigation into size effects in quasi-isotropic carbon/epoxy laminates with sharp and blunt notches”, Composites Science and Technology, vol. 100, pp. 220–227, 2014.